Skip to content
PHOENIX TECHNOLOGIES, BANGALORE | 📞 Call us on 080 42100546, Mob : 7760459320 | Email : info@phoenixtechnologies.org
PHOENIX TECHNOLOGIES, BANGALORE | 📞 Call us on 080 42100546, Mob : 7760459320 | Email : info@phoenixtechnologies.org

Schneider ATV310HU55N4E

Rs. 0.00
SKU ATV310HU55N4E
Main
range of product

Altivar Easy 310

product or component type

Variable speed drive

product specific application

Simple machine

assembly style

With heat sink

device short name

ATV310

network number of phases

Three phase

[Us] rated supply voltage

380...460 V (- 15...10 %)

motor power kW

5.5 kW

motor power hp

7.5 hp

noise level

50 dB

Complementary
product destination

Asynchronous motors

quantity per set

Set of 1

EMC filter

Without EMC filter

type of cooling

Integrated fan

supply frequency

50/60 Hz +/- 5 %

communication port protocol

Modbus

connector type

RJ45 for Modbus on front face

physical interface

2-wire RS 485 for Modbus

transmission frame

RTU for Modbus

transmission rate

4800 bit/s

9600 bit/s
19200 bit/s
38400 bit/s
number of addresses

1...247 addresses for Modbus

communication service

Read holding registers (03), messaging: 29 words

Write single register (06), messaging: 29 words
Write multiple registers (16), messaging: 27 words
Read/write multiple registers (23), messaging: 4/4 words
Read device identification (43)
line current

14.3 A

apparent power

11.4 kVA

prospective line Isc

<= 5 kA

continuous output current

12.6 A at 4 kHz

maximum transient current

18.9 A for 60 s

power dissipation in W

141.54 W at In

speed drive output frequency

0.5...400 Hz

nominal switching frequency

4 kHz

switching frequency

2...12 kHz (adjustable)

speed range

1...20

transient overtorque

170...200 % of nominal motor torque depending on drive rating and type of motor

braking torque

Up to 150 % of nominal motor torque with braking resistor at high inertia

Up to 70 % of nominal motor torque without braking resistor
asynchronous motor control profile

Energy saving ratio

Quadratic voltage/frequency ratio
Sensorless flux vector control
motor slip compensation

Adjustable

Preset in factory
output voltage

380...460 V three phase

electrical connection

4 mm² at terminal L1, L2, L3, PA/+, PB, U, V, W

tightening torque

1.2...1.4 N.m

insulation

Electrical between power and control

supply

Internal supply for reference potentiometer : 5 V (4.75...5.25 V) DC 10 mA with overload and short-circuit protection

Internal supply for logic inputs : 24 V (20.4...28.8 V) DC 100 mA with overload and short-circuit protection
analogue input number

1

analogue input type

Configurable current (AI1) 0...20 mA, impedance 250 Ohm

Configurable voltage (AI1) 0...10 V, impedance 30 kOhm
Configurable voltage (AI1) 0...5 V, impedance 30 kOhm
discrete input number

4

discrete input type

24 V (18...30 V) programmable, at LI1...LI4 terminal(s)

discrete input logic

Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)

Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
sampling duration

10 ms for analogue input

20 ms, tolerance +/- 1 ms for logic input
linearity error

+/- 0.3 % of maximum value for analogue input

analogue output number

1

analogue output type

AO1 software-configurable voltage : 0...10 V, impedance: 470 Ohm, resolution 8 bits

AO1 software-configurable current : 0...20 mA, impedance: 800 Ohm, resolution 8 bits
discrete output number

2

discrete output type

(LO+, LO-) logic output

(R1A, R1B, R1C) protected relay output 1 C/O
minimum switching current

5 mA at 24 V DC for logic relay

maximum switching current

2 A at 250 V AC on inductive load (cos phi = 0.4 L/R = 7 ms) for logic relay

2 A at 30 V DC on inductive load (cos phi = 0.4 L/R = 7 ms) for logic relay
3 A at 250 V AC on resistive load (cos phi = 1 L/R = 0 ms) for logic relay
4 A at 30 V DC on resistive load (cos phi = 1 L/R = 0 ms) for logic relay
acceleration and deceleration ramps

S

U
Linear from 0...999.9 s
braking to standstill

By DC injection, <= 30 s

protection type

Against input phase loss in three-phase

Thermal motor protection via the drive by continuous calculation of I²t
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
frequency resolution

Converter A/D, 10 bits for analog input

0.1 Hz for display unit
time constant

20 ms, tolerance +/- 1 ms for reference change

operating position

Vertical +/- 10 degree

height

151 mm

width

140 mm

depth

184 mm

product weight

1.8 kg

Environment
electromagnetic compatibility

Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11

Electrical fast transient/burst immunity test (test level: level 4) conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test (test level: level 3) conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances (test level: level 3) conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test (test level: level 3) conforming to EN/IEC 61000-4-3
Surge immunity test (test level: level 3) conforming to EN/IEC 61000-4-5
standards

EN/IEC 61800-3

EN/IEC 61800-5-1
IP degree of protection

IP41 on top

IP20 without blanking plate on upper part
pollution degree

2 conforming to EN/IEC 61800-5-1

environmental characteristic

Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3

Dust pollution resistance class 3S2 conforming to EN/IEC 60721-3-3
shock resistance

15 gn (duration = 11 ms) conforming to EN/IEC 60068-2-27

relative humidity

5...95 % (without condensation) conforming to IEC 60068-2-3

5...95 % (without dripping water) conforming to IEC 60068-2-3
ambient air temperature for storage

-25...70 °C

ambient air temperature for operation

-10...55 °C without derating

55...60 °C protective cover from the top of the drive removed with current derating 2.2 % per °C
operating altitude

<= 1000 m without derating

Schneider ATV310HU55N4E
Documents & Downloads
Product datasheet
Instruction sheet
Catalogue