Skip to content
PHOENIX TECHNOLOGIES, BANGALORE | 📞 Call us on 080 42100546, Mob : 7760459320 | Email : info@phoenixtechnologies.org
PHOENIX TECHNOLOGIES, BANGALORE | 📞 Call us on 080 42100546, Mob : 7760459320 | Email : info@phoenixtechnologies.org

Schneider ATV12H075M2

Rs. 0.00
SKU ATV12H075M2
Main
range of product

Altivar 12

product or component type

Variable speed drive

product destination

Asynchronous motors

product specific application

Simple machine

assembly style

With heat sink

component name

ATV12

quantity per set

Set of 1

EMC filter

Integrated

built-in fan

Without

network number of phases

1 phase

[Us] rated supply voltage

200...240 V - 15...10 %

motor power kW

0.75 kW

motor power hp

1 hp

communication port protocol

Modbus

line current

10.2 A 200 V

8.5 A 240 V
speed range

1...20

transient overtorque

150...170 % of nominal motor torque depending on drive rating and type of motor

asynchronous motor control profile

Quadratic voltage/frequency ratio

Sensorless flux vector control
Voltage/frequency ratio (V/f)
IP degree of protection

IP20 without blanking plate on upper part

noise level

0 dB

Complementary
supply frequency

50/60 Hz +/- 5 %

connector type

1 RJ45 Modbus on front face

physical interface

2-wire RS 485 Modbus

transmission frame

RTU Modbus

transmission rate

4800 bit/s

9600 bit/s
19200 bit/s
38400 bit/s
number of addresses

1...247 Modbus

communication service

Read holding registers (03) 29 words

Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
prospective line Isc

<= 1 kA

continuous output current

4.2 A 4 kHz

maximum transient current

6.3 A 60 s

speed drive output frequency

0.5...400 Hz

nominal switching frequency

4 kHz

switching frequency

2...16 kHz adjustable

4...16 kHz with derating factor
braking torque

Up to 70 % of nominal motor torque without braking resistor

motor slip compensation

Adjustable

Preset in factory
output voltage

200...240 V 3 phases

electrical connection

Terminal 3.5 mm² AWG 12 L1, L2, L3, U, V, W, PA, PC

tightening torque

0.8 N.m

insulation

Electrical between power and control

supply

Internal supply for reference potentiometer 5 V DC 4.75...5.25 V 10 mA overload and short-circuit protection

Internal supply for logic inputs 24 V DC 20.4...28.8 V 100 mA overload and short-circuit protection
analogue input number

1

analogue input type

Configurable voltage AI1 0...10 V 30 kOhm

Configurable voltage AI1 0...5 V 30 kOhm
Configurable current AI1 0...20 mA 250 Ohm
discrete input number

4

discrete input type

Programmable LI1...LI4 24 V 18...30 V

discrete input logic

Negative logic (sink) > 16 V < 10 V 3.5 kOhm

Positive logic (source) 0...< 5 V > 11 V
sampling duration

20 ms +/- 1 ms logic input

10 ms analogue input
linearity error

+/- 0.3 % of maximum value analogue input

analogue output number

1

analogue output type

Software-configurable voltage AO1 0...10 V 470 Ohm 8 bits

Software-configurable current AO1 0...20 mA 800 Ohm 8 bits
discrete output number

2

discrete output type

Logic output LO+, LO-

Protected relay output R1A, R1B, R1C 1 C/O
minimum switching current

5 mA 24 V DC logic relay

maximum switching current

2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay

2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
acceleration and deceleration ramps

Linear from 0 to 999.9 s

S
U
braking to standstill

By DC injection <= 30 s

protection type

Against input phase loss in three-phase

Thermal motor protection via the drive by continuous calculation of I²t
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
frequency resolution

0.1 Hz display unit

Converter A/D, 10 bits analog input
time constant

20 ms +/- 1 ms for reference change

marking

CE

operating position

Vertical +/- 10 degree

height

143 mm

width

72 mm

depth

131.2 mm

product weight

0.8 kg

functionality

Basic

specific application

Commercial equipment

Variable speed drive application selection

Commercial equipment : mixer

Commercial equipment : other application
Textile : ironing
motor starter type

Variable speed drive

Environment
electromagnetic compatibility

Immunity to conducted disturbances level 3 EN/IEC 61000-4-6

Surge immunity test level 3 EN/IEC 61000-4-5
Voltage dips and interruptions immunity test EN/IEC 61000-4-11
Electrical fast transient/burst immunity test level 4 EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 EN/IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 EN/IEC 61000-4-3
electromagnetic emission

Radiated emissions environment 1 category C2 EN/IEC 61800-3 2...16 kHz shielded motor cable

Conducted emissions with integrated EMC filter environment 1 category C1 EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable 5 m
Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2...12 kHz shielded motor cable 5 m
Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable 10 m
Conducted emissions with additional EMC filter environment 1 category C1 EN/IEC 61800-3 4...12 kHz shielded motor cable 20 m
Conducted emissions with additional EMC filter environment 1 category C2 EN/IEC 61800-3 4...12 kHz shielded motor cable 50 m
Conducted emissions with additional EMC filter environment 2 category C3 EN/IEC 61800-3 4...12 kHz shielded motor cable 50 m
product certifications

CSA

C-Tick
GOST
NOM
UL
vibration resistance

1 gn EN/IEC 60068-2-6 13...200 Hz

1.5 mm peak to peak EN/IEC 60068-2-6 3...13 Hz drive unmounted on symmetrical DIN rail
shock resistance

15 gn EN/IEC 60068-2-27 11 ms

relative humidity

5...95 % without condensation IEC 60068-2-3

5...95 % without dripping water IEC 60068-2-3
ambient air temperature for storage

-25...70 °C

ambient air temperature for operation

-10...40 °C protective cover from the top of the drive removed

40...60 °C with current derating 2.2 % per °C
operating altitude

> 1000...2000 m with current derating 1 % per 100 m

<= 1000 m without derating
Offer Sustainability
Sustainable offer status

Green Premium product

RoHS (date code: YYWW)

Schneider Electric declaration of conformity

REACh

Reference not containing SVHC above the threshold

Product environmental profile

Product Environmental Profile

Product end of life instructions

End of Life Information

Contractual warranty
Warranty period

12 months

Schneider ATV12H075M2
Documents & Downloads
Product datasheet
User guide
Catalogue